Led Flashing Brake Light Braker Module Installtion Instructions | Autolumination
Home

Contact Us

Email: superlumination@cox.net

Search

 



MENU HERE

Leds + Flashing Brake Light = Double Safety

 

Read How LED Stop Lamps Reduce the Number & Severity of  Automobile Accidents

Read safety studies of flashing brake lights

Click Here to view a YouTube video

General Notes:

One module can connect to more than one led bulb, but each bulb must be connected to a module in order for that light to flash.  In most instances (to avoid running extra wiring) , it is easiest to install one module at each led light (ie: one module on each side of the vehicle).  If you have more than one brake light on each side of the vehicle, one module can  be used on each side (2 modules for four lights).

Important:  The FM-00 dual circuit module has the words "FLASHING CONTROL MODULE" molded into the black case.  The end closest to the word "FLASHING" must be toward the battery, and the word "MODULE" must be oriented closest to the led bulb.  If the module is installed backwards, it will not work.

**Operating Voltage: 6 - 13.5 volts

Maximum Current : 800ma

 

Note: These modules are not suited for filament style bulbs.  A filament style bulb is not capable of fast switching, and cannot strobe.  The power draw of the filament style bulb will destroy the Flashing Modules.

FLASHING LED CONTROL MODULES

The FM-00, FM-01 and FM-02 BRAKER CONTROL MODULES CAN MAKE YOUR led brake lights or reverse lights strobe brightly for a few seconds every time you hit the brakes or switch into reverse.

.........After a few seconds the lights stays bright as long as your foot is on the brake or the vehicle is in reverse.

The FM-01 and FM-02 BRAKER CONTROL MODULES CAN MAKE any led lights strobe continuously.

The FM-03 BRAKER CONTROL MODULES CAN MAKE YOUR led brake lights or reverse lights strobe brightly for a few seconds every time you hit the brakes or switch into reverse.

.........After a few seconds the lights stays bright as long as your foot is on the brake or the vehicle is in reverse.  The module will then strobe again for 2 seconds when the pedal is first released or when you switch out of reverse.

 *WORKS WITH ANY LED LIGHTS

WORKS GREAT FOR LED BRAKE LIGHT OR REVERSE LIGHT BULB

Works great for upper 3d brake lights too!

*Note: May not work with some vehicles that modulate voltage to a single circuit bulb for brake indication.  Also may not work in some vehicles if the circuit does not completely shut off power when the brake is released.

Led Strobe Module Led Strobe Module
Brake Lights Reverse Lights Continuous
10 Hz (10 flashes/sec)
Continuous
 20 Hz (20 flashes/sec)
Click on images above for larger view
Click Here to view a YouTube video
Click Here for Detailed Operation & Installation Instructions  
Dual Function:

White Wire: Strobes for 2 seconds When you First Brake or Switch into Reverse.
Blue Wire: Strobes Constantly
Single Function:

Strobes When you First Brake and Again When you Release the Brake
Dual Function:

White Wire: Strobes for 2 seconds When you First Brake or Switch into Reverse.
Blue Wire: Strobes Constantly
Single Function:

Red
STYLE="font-size: xx-small"> Wire: Strobes for 2 seconds When you First Brake or first shift into reverse.
Single Function:

Blue
Wire: Strobes for 2 seconds When you First Brake or first shift into reverse.
Led Strobe Module Led Strobe Module Led Strobe Module Flashing LED Brake Light Module
FM-02A (10 Hz) FM-02B (20 Hz) FM-03A (10 Hz) FM-03B (20 Hz) FM-01A (10 Hz) FM-01B (20 Hz) FM-00 (20 Hz) Miniature Module FM-04 (20 Hz)
With Continuous or Intermittent Strobe Modes With Intermittent Strobe Mode on Brake and Release With Continuous or Intermittent Strobe Modes With Intermittent Strobe Mode on Brake With Intermittent Strobe Mode on Brake or Reverse

Universal Compact Two Function Strobe Module

Improved Design

Only 1-3/4" x 1-3/8" x 1"

New design has no battery to burn out

Universal Compact Strobe Module

Improved Design

Only 1-3/4" x 1-3/8" x 1"

New design has no battery to burn out

Universal Two Function Strobe Module

3-3/8"x 2"x 7/8"

New design has no battery to burn out

Dual Compact Circuit Braker Module

2"x 1"x 3/8"

New design has no battery to burn out

ZE="7">

Dual Compact Circuit Braker Module

2-3/4"x 1-1/2"x 1"

$9.99 EA

$9.99 EA

$8.99 EA

$ 5.99 EA

$ 6.99 EA

Choose Color

 

Choose Speed

 

Choose Color

 

Choose Speed

 

Choose Color

 

Choose Speed

 

Choose Color

 

Choose Speed

 

Choose Color

 

Choose Speed

 

Uses: 

7507, 1156,3156, 7440, 921 single circuit bulbs & 7225, 1157, 3157, 7443 dual circuit bulbs, or use with any led light bulb or led fixture.  **Can be used in any 6 or 12 volt (-) ground or (+) ground systems.

 

Common Applications:

Brake light Warning Strobe
Reverse Light Warning Strobe

Make any led bulbs or lights strobe continuously.STYLE="font-size: xx-small">

Function:

The FM-02 module contains a chip that will cause an led light bulbs to operate as follows (Note: Use either the White wire or Blue wire not both):

 

Function 1 (If you use the White Wire)

1.  Each time power is applied to the red wire, from the battery, the white wire to the led bulb will cause the led bulb to perform a sequence as follows;

A.  The led will strobe brightly for a few seconds and then stop strobing.

B.  After a few seconds of strobing, the led light will light bright in a constant-on mode for as long as power is continually applied to the circuit (ie: as long as the brake pedal is pressed).

*C.  When power is cut to the red wire (ie: the brake pedal is released, the bulb will go dim.  

 

*Note 1: In a singe circuit bulb such as an 1156 or 921, there is no dim circuit, so the module will sequence whenever the brake is applied, but there will be no dim function.

 

Function 2 (If you use the Blue Wire)

1.  Each time power is applied to the red wire, from the battery, the blue wire to the led bulb will cause the led bulb to strobe continuously until power to the red wire is off.

 

*Note 1: In a singe circuit bulb such as an 1156 or 921, there is no dim circuit, so the module will sequence whenever the brake is applied, but there will be no dim function.

 

**Note 2: This module can also be used in a positive ground 6 or 12 volt electrical system.

Uses: 

7507, 1156,3156, 7440, 921 single circuit bulbs & 7225, 1157, 3157, 7443 dual circuit bulbs, or use with any led light bulb or led fixture.  **Can be used in any 6 or 12 volt (-) ground or (+) ground systems

 

Common Applications:

Brake light Warning Strobe
Reverse Light Warning Strobe

 

The FM-03 module contains a chip that will cause an led light bulbs to operate as follows:

 

 

1.  Each time power is applied to the white wire, from the brake circuit,  the led bulb will perform a sequence as follows;

A.  The led will strobe brightly for a few seconds and then stop strobing.

B.  As long as power is still applied from the white-blue brake wire, the led light will light bright for as long as power is continually applied to the circuit (ie: as long as the brake pedal is pressed).

* B.  When power is cut to the white wire (ie: the brake pedal is released, the bulb will flash again for 2 seconds and then  go dim.

 

* Note: In a singe circuit bulb such as an 1156 or 921, there is no dim circuit, so the module will sequence whenever the brake is applied, but there will be no dim function.

 

**Note 2: This module can also be used in a positive ground 6 or 12 volt electrical system.

Uses: 

7507, 1156,3156, 7440, 921 single circuit bulbs & 7225, 1157, 3157, 7443 dual circuit bulbs, or use with any led light bulb or led fixture.  **Can be used in any 6 or 12 volt (-) ground or (+) ground systems,

 

Common Applications:

Brake light Warning Strobe
Reverse Light Warning Strobe

Make any Led bulbs or lights strobe continuously.

Function:

The FM-01 module contains a chip that will cause an led light bulbs to operate as follows (Note: Use either the White wire or Blue wire not both):

 

Function 1 (If you use the White Wire)

1.  Each time power is applied to the red wire, from the battery, the white wire to the led bulb will cause the led bulb to perform a sequence as follows;

A.  The led will strobe brightly for a few seconds and then stop strobing.

B.  After a few seconds of strobing, the led light will light bright in a constant-on mode for as long as power is continually applied to the circuit (ie: as long as the brake pedal is pressed).

*C.  When power is cut to the red wire (ie: the brake pedal is released, the bulb will either go dim.

 

*Note 1: In a singe circuit bulb such as an 1156 or 921, there is no dim circuit, so the module will sequence whenever the brake is applied, but there will be no dim function.

 

Function 2 (If you use the Blue Wire)

1.  Each time power is applied to the red wire, from the battery, the blue wire to the led bulb will cause the led bulb to strobe continuously until power to the red wire is off.

 

*Note 1: In a singe circuit bulb such as an 1156 or 921, there is no dim circuit, so the module will sequence whenever the brake is applied, but there will be no dim function.

 

**Note 2: This module can also be used in a positive ground 6 or 12 volt electrical system.

 

Uses: 

7507, 1156,3156, 7440, 921 single circuit bulbs & 7225, 1157, 3157, 7443 dual circuit bulbs, or use with any led light bulb or led fixture.  **Can be used in any 12 volt (-) ground or (+) ground systems. Will not work in 6 volt systems.

Common Applications:

Brake light Warning Strobe
Reverse Light Warning Strobe

Function:

The FM-00 module contains a chip that will cause an led light bulb or any 12 volt led light to operate as follows:

 

1.  Each time power is applied to the red wire, from the battery, the black wire to the led bulb will cause the led bulb to perform a sequence as follows;

A.  The led will strobe brightly for a few seconds and then stop strobing***.

B.  After a few seconds of strobing, the led light will light bright in a constant-on mode for as long as power is continually applied to the circuit (ie: as long as the brake pedal is pressed).

*C.  When power is cut to the red wire (ie: the brake pedal is released, the bulb will go dim.

 

*Note 1: In a singe circuit bulb such as an 1156 or 921, there is no dim circuit, so the module will sequence whenever the brake is applied, but there will be no dim function.

 

**Note 2: This module can also be used in a positive ground 12 volt electrical system. 

*** Note 3:  The FM-00 has a built in circuit that will temporarily suspend the strobing effect if the brake pedal is pressed repeatedly.  The strobe chip sill only reset if the brake is released for about 5 seconds or more. 
Uses: 

7507, 1156,3156, 7440, 921 single circuit bulbs & 7225, 1157, 3157, 7443 dual circuit bulbs, or use with any led light bulb or led fixture.  **Can be used in any 6 or 12 volt (-) ground or (+) ground systems

Common Applications:

Brake light Warning Strobe
Reverse Light Warning Strobe

Function:

 

The FM-01 module contains a chip that will cause an led light bulb or any 6 or 12 volt led light to operate as follows:

 

1.  Each time power is applied to the brown wire, from the battery, the black wire to the led bulb will cause the led bulb to perform a sequence as follows;

A.  The led will strobe brightly for a few seconds and then stop strobing.

B.  After a few seconds of strobing, the led light will light bright in a constant-on mode for as long as power is continually applied to the circuit (ie: as long as the brake pedal is pressed).

*C.  When power is cut to the brown wire (ie: the brake pedal is released, the bulb will either go dim.

 

*Note 1: In a singe circuit bulb such as an 1156 or 921, there is no dim circuit, so the module will sequence whenever the brake is applied, but there will be no dim function.

 

**Note 2: This module can also be used in a positive ground 12 volt electrical system.  If you have a (+) positive ground volt system, The module must be installed inline in the (+) Ground wire and the blue wire must be installed toward the led light or bulb.  The brown wire must be installed toward the bulb.

Installation:

Install the module anywhere between the battery power and the led light that you wish to make flash.  Connect the wires as follows:

Connect the flashing module in the wires feeding to any led bulb as follows:

White Wire - Connect to the (+) side of any led light(s) that you want to strobe intermittently for the first 20 ms).

Red Wire - Connect to (+) Wire on the Power or Battery Side.

Black Wires - Splices into to the - ground wires on both sides.

Blue Wire - Connect to the (+) side of any led light(s) that you want to strobe continuously.

 

Note 1 :  You do not have to use both the white wires and the blue wires at the same time.  You can and normally would use one or the other.

 

****WARNING**** Never allow any of the bare wires connected to the module to touch together if power is connected to the module.  This can instantly and permanently damage the module. 

Installation:

Install the module anywhere between the battery power and the led light that you wish to make flash.  Connect the wires as follows:

Connect the flashing module in the wires feeding to any led bulb as follows:

* Blue Input Wire - Connect to the (+) battery power to power the module.

White Input Wire - Connect to (+) Brake Circuit.

Black Input Wire - Connect to the - ground wire.

Red Output Wire - Connect to the (+) side of any led light(s) or Bulb(s).

Black Output Wire - Connect to to the - ground wire going to the led light.

 

* Note:  You must connect the blue wire to a 12+ constant-on circuit.  This circuit must have + power on after the brake pedal is released of the light will not flash when the brake pedal is released. 

 

****WARNING**** Never allow any of the bare wires connected to the module to touch together if power is connected to the module.  This can instantly and permanently damage the module. 

 

Installation:

Install the module anywhere between the battery power and the led light that you wish to make flash.  Connect the wires as follows:

 

Connect the flashing module in the wires feeding to any led bulb as follows:

White Wire - Connect to the (+) side of any led light(s) that you want to strobe intermittently for the first 20 ms).

Red Wire - Connect to (+) Wire on the Power or Battery Side.

Black Wires - Splices into to the - ground wires on both sides.

Blue Wire - Connect to the (+) side of any led light(s) that you want to strobe continuously.

 

Note:  You do not have to use both the white wires and the blue wires at the same time.  You can and normally would use one or the other.

 

****WARNING**** Never allow any of the bare wires connected to the module to touch together if power is connected to the module.  This can instantly and permanently damage the module. 

Installation:

The FM-00 module can be used in conventional (-) ground systems and (+) ground 12 volt systems.  It will not work in 6 volt systems.

Install the module anywhere between the battery power and the led light that you wish to make flash.  Connect the wires as follows:

Connect the flashing module in the wires feeding to any led bulb as follows:

Important:  The dual circuit module has the words "FLASHING CONTROL MODULE" molded into the black case.  The end closest to the word "FLASHING" must be toward the battery, and the word "MODULE" must be oriented closest to the led bulb.  If the module is installed backwards, it will not work.

Power must flow thru the module and then to the led lights or bulbs that you want to make flash.

Red Wires - Connects to the (+) brake light wire.

Black Wires - Connects to the (-) ground wire.

 

****WARNING**** Never allow any of the bare wires connected to the module to touch together if power is connected to the module.  This can instantly and permanently damage the module. 

Installation {Conventional (-) ground system} :

Install the module anywhere between the battery power and the led light that you wish to make flash.  Connect the wires as follows:

Connect the brown wire to the wire coming from the (+) battery side of the circuit.

Connect the blue wire to the (+) wire going to the led light or light bulb.

Installation {Positive (+) ground system} :

Install the module anywhere between the battery power and the led light that you wish to make flash.  Connect the wires as follows:

Connect the blue  wire to the wire coming from the (+) battery side of the circuit.

Connect the brown wire to the (+) wire going to the led light or light bulb.

****WARNING**** Never allow any of the bare wires connected to the module to touch together if power is connected to the module.  This can instantly and permanently damage the module. 




Operating Voltage: 11.5 - 13.5 volts

Maximum Current : 800ma

Note: These modules are not suited for filament style bulbs.  A filament style bulb is not capable of fast switching, and cannot strobe.  The power draw of the filament style bulb will destroy the Braker Flashing Modules.


2 Circuit 12 Volt LED WIG WAG Safety Strobe Controller

Strobe rate is adjustable from 1 flash per second up to 3 flashes per second on each side.

Strobe sequence Wig WAG alternates (2 flashes left followed by 2 flashes right) between the right tube & left tube

With rubber grommet for installation in a 5/8" hole

For use with any led bulbs or led lights we sell

Turns any led bulbs or lights into an instant emergency flasher/ warning system

Click on images above  for larger view

Note: This truck is outfitted with our 3157 48 LED SMT Bulbs  

+ Led WIG-WAG Controller

Strobe Light

Manual On/Off Switch (Optional)

Connects to 12 volts

$19.99 With Manual Switch $17.99 No Switch


Universal Braker Car Alarm Laser Fog Light Rear Anti-Collision Taillight Warning Lamp

Connect to Brake Light Circuit

Universal Braker Car Alarm Laser Fog Light Rear Anti-Collision Taillight Warning Lamp

Universal Braker Car Alarm Laser Fog Light Rear Anti-Collision Taillight Warning Lamp Patterned

Straight Line Patterned
$9.99 Ea.
Enter Quantity
Choose Color
Choose Type


INTELLIGENT DOME LIGHT DIMMER FADER

1.25 AMP (15 WATT) CAPACITY

3-1/8" X 1-1/4" X 7/8" Thick

DIMMER ACTIVATED BY DOOR SWITCH

1.  Slowly brightens when door opens (8 seconds)

2.  Slowly brightens when door opens (8 seconds)

3. Auto shut-off after 10 seconds 

Intelligent Dome Light Contoller Dimmer

Order Controller (above): $19.99 ea.

Choose Color

 

Choose Type  

 


Wireless Remote Control

on/off Switch

12 Volt DC Input

60 watt maximum output.

5 amp capacity.

26mm x 54mm x 26mm Deep

1" x 2" x1" Deep

12 Volt input.

12 Volt output.

Wires wireless transmitter

Capacity:
  • (50) 3led utility lights
  • (50) 8led utility lights
  • (30) 24led utility lights
  • (30) 13led utility lights
  • (30) LED Strobes
  • (30) Bright Strobes
  • (30) MR16 18led bulbs
  • (140) 9led festoon bulbs

$19.99 Each

Choose Color 

Choose Type 

LED Flasher Module

2 VDC Input

6 watt maximum output.

500 milliamp capacity.

Slow - 20-30 cylces per minute

Fast - 90-200 cycles per minute

75mm x 65mm x 30mm Deep

3" x 2-1/2" x1-1/8" Deep

12 Volt input.

12 Volt output.

2 screw mount

Capacity:
  • (5) 3led utility lights
  • (5) 8led utility lights
  • (3) 24led utility lights
  • (3) 13led utility lights
  • (3) LED Strobes
  • (3) Bright Strobes
  • (3) MR16 18led bulbs
  • (14) 9led festoon bulbs

$2.99 Each

Choose Color 

Choose Type 

Manual ON/OFF LED Switch Module (With Flash)

2 VDC Input

6 watt maximum output.

500 milliamp capacity.

Flashes at 90-200 cycles per minute

75mm x 65mm x 30mm Deep

3" x 2-1/2" x1-1/8" Deep

12 Volt input.

12 Volt output.

2 screw mount

Capacity:
  • (5) 3led utility lights
  • (5) 8led utility lights
  • (3) 24led utility lights
  • (3) 13led utility lights
  • (3) LED Strobes
  • (3) Bright Strobes
  • (3) MR16 18led bulbs
  • (14) 9led festoon bulbs

$3.99 Each

Choose Type 

Choose Type 

Manual ON/OFF LED Switch Module (No Flash)

2 VDC Input

6 watt maximum output.

500 milliamp capacity.

75mm x 65mm x 30mm Deep

3" x 2-1/2" x1-1/8" Deep

12 Volt input.

12 Volt output.

2 screw mount

Capacity:
  • (5) 3led utility lights
  • (5) 8led utility lights
  • (3) 24led utility lights
  • (3) 13led utility lights
  • (3) LED Strobes
  • (3) Bright Strobes
  • (3) MR16 18led bulbs
  • (14) 9led festoon bulbs

$2.99 Each

Choose Type 

Choose Type 

Strobe Light Manual Steel on/off Toggle Switch With wires & fuse

Thru Hole Screw Mount

$2.99 Each

Choose Color 

Choose Type 


UPIC Shipping Insurance

Note: Our packages are not automatically insured against loss during shipping.  Insurance is the responsibility of the purchaser!
$2.00 for each $100 unit of insurance

Shipping Insurance

$2.00 per $100


Links 
Automotive Replacement  Light Bulbs: Other Auto & Motorcycle Lighting: Low Voltage Utility Lights & Fixtures   Truck 4X4 RV & Trailer Lighting   Household, Commercial & Industrial Lighting    Other Products    Reference:
1156 1157 1142 2357 7507 7225 Bayonet Tail-Brake Turn Signal Back-Up LED Light Fixtures & Strobes LED Light Fixtures & Strobes  Semi, Truck & Truck Trailer LEDS  Lights For the Home, Yard & Garden  LED Windshield Washer & Mirror Turn Signal Indicators Specs
3157 3156  3457 4157 3057 Wedge Tail-Brake-Turn Signal & Back-Up Bulbs  Light Bright NEON Glow Wire LED Strips, Led Strings. Led Bars Clearance and Side Marker Lights LED Strips, Led Strings. Led Bars  LED Flashers, Protectors, Load Equalizers Turn Signal Fix Cross Reference
7443 7440 Wedge Tail-Brake-Turn Signal & Back-Up Bulbs  LED Neo-Neon Flexible NEON Light Tubing LED Strips Connectors, Adapters & Mounting Hardware Tail Stop Work & Turn Signal Lights  MR11, MR16 GU10 Bulbs  Electrical Contacts, Sockets, Connectors & Fuses Technical Data
194 168 2825 W5W Wedge Side Marker License Plate &  Interior Bulbs  HID Headlight Fog Light & Reverse Light Systems   Control Modules & Power Supplies Indicator Lights  LED Light Fixtures for the Home & RV  Led Controllers, Flashing Modules, Braker Modules & Dimmers Bulb Dimensions
37 74 Gauge & Instrument Panel & Neo-Wedge  Bulbs  Daytime Running Light (DRL) Kits and Fog Light Systems  Overhead & Under Cabinet Lighting _ Trucks - Boats & RV's    Overhead Cab Lighting      Track Lights  Miniature Train Bulbs & Parts General Bulb Information
3022 3122 561 578 6418 6411 Festoon Dome Bulbs  LED Screw Mount Indicator & Accent  Lights LED Light Fixtures for the Home Boat & RV  Daytime Running Light (DRL) Kits and Fog Light Systems  LED Neo-Neon Flexible NEON Light Tubing  Universal Programmable Remote Controllers & Switches for Garage Door Openers Application Charts
Ba9s, E10, Ba7s, Small Ba15s and Bay15d Bayonet Bulbs  LED & Neon Light Tubes & Underbody Light Kits LED Bike, Go Ped, Motorcycle, ATV, Boat and RV Light Fixtures  Connectors & Grommets   LVD Electromagnetic Induction Bulbs  Discrete Raw Leds, Resistors & Components Bases & Filaments
< 906 921 Wedge Stop & Interior Bulbs  LED Windshield Washer & Mirror Turn Signal Indicators LED Screw Mount Indicator & Accent  Lights       Power Inverters  - Power Supplies  - Power Adapters  Led Resistor Calculations
Headlights DRL & Foglights  Overhead Cab Lighting  LED Flashlights Work Lights & Bulbs  Shipping
HID Systems  Angel Eye Halo Rings for Headlights Tail Lights & Lenses       LED Bike, Go Ped, Motorcycle, ATV, Boat and RV Light Fixtures   Mail Orders
 6 Volt Antique - Vintage Bulbs  & 24 volt LED Flashing Dimming & Wig -Wag Modules         Electrical Wire & Shrink Tubing  International Shipping
 L1142 1076 1176 Boat & Marine Bulbs Power Inverters  - Power Supplies  - Power Adapters        Motorcycle & RV Running Lights, Turn Signals & Indicator Lights   FAQ'S
 Dura Chrome Titanium Platinum Silver Vision Bulbs Switchback Bulbs Two-Color Turn Signal Running Lights Air Horns   Policies
   Xenon Plasma Super Hyper White Bulbs         Vinyl Protective Film for Tinting Headlights, Tail Lights & Lenses   Visual Bulb Finder
 G4 T10 2 Pin Bi- Pin Vinyl 3D Carbon Fiber Decorative Self-Adhesive Film Lookup Order & Tracking Number 
              Sitemap
 Canbus Error Free Bulbs BMW Mercedes Audi VW Volvo Dodge 5002S PY24W            
   Weekly Sale Items     CarInfoTech          

Powered by Ewebmerchant.com

Quick-n-EZ Shopping Cart ®